高流动性PA66 德国巴斯夫 A3X2G5 加25%玻纤 电气性好 阻燃 高刚性

PA塑料(尼龙)

(聚酰胺)

称:Polyamide　 比重:PA6-1.14克/立方厘米PA66-1.15克/立方厘米 PA1010-1.05克/立方厘米 成型收缩率:PA6-0.8-2.5% PA66-1.5-2.2%成型温度：220-300℃ 干燥条件：100-110℃ 12小时

坚韧,耐磨,耐油,耐水,抗酶菌,但吸水大.

尼龙6弹性好,冲击强度高,吸水较大

尼龙66性能优于尼龙6,强度高,耐磨性好

尼龙610与尼龙66相似,但吸水小,刚度低

尼龙1010半透明,吸水小,耐寒性较好适于制作一般机械零件,减磨耐磨零件,传动零件,以及化工,电器,仪表等零件

供应PA66德国巴斯夫A3WG315％玻璃纤维增强

供应PA66德国巴斯夫A3HG5

供应PA66德国巴斯夫8233G.25％玻璃纤维增强

供应PA66德国巴斯夫A3WG6.30％玻璃纤维增强

供应PA66德国巴斯夫A3EG5.25％玻璃纤维增强

供应PA66德国巴斯夫A3EG7.BK2318935％玻璃纤维增强

供应PA66德国巴斯夫A3HG7.35％玻璃纤维增强

未增强UltramidA,B(尼龙6,66)

PA66尼龙A3K--注塑级。含稳定剂，流动性好。适合电器绝缘制品和工程零件。

PA66尼龙A3W--注塑级，耐热老化。适于长期高温使用的零件。

PA66尼龙B3S--注塑级。容易流动，固化快，含稳定剂。适合薄壁制品如罩，夹具，销钉，夹板等，紧固件。 

PA plastic (nylon)

(Polyamide)

Scale: Polyamide Specificgravity: PA6-1.14g/cm3 PA66-1.15g/cm3 PA1010-1.05g/cm3 Moldingshrinkage: PA6-0.8-2.5% PA66-1.5-2.2% Molding temperature: 220-300℃ Drying conditions: 100-110 ℃ 12 hours

Tough, wear-resistant, oilresistant, water resistant, enzyme resistant, but with high waterabsorption

Nylon 6 has good elasticity,high impact strength, and high water absorption

Nylon 66 has better performancethan nylon 6, high strength, and good wear resistance

Nylon 610 is similar to nylon66, but has low water absorption and stiffness

Nylon 1010 is semi transparent,with low water absorption and good cold resistance. It is suitablefor making general mechanical parts, wear reducing andwear-resistant parts, transmission parts, as well as chemical,electrical, instrument and other parts

Supply PA66 German BASFA3WG315% glass fiber reinforced

Supply PA66 BASF A3HG5,Germany

Supply PA66 BASF Germany8233G.25% glass fiber reinforced

Supply PA66 German BASFA3WG6.30% glass fiber reinforced

Supply PA66 German BASFA3EG5.25% glass fiber reinforced

Supply PA66 BASF GermanyA3EG7.BK2318935% glass fiber reinforced

Supply PA66 German BASFA3HG7.35% glass fiber reinforced

Unreinforced UltramedA, B(nylon 6,66)

PA66 nylon A3K - injectiongrade. Contains stabilizers and has good flowability. Suitable forelectrical insulation products and engineering parts.

PA66 nylon A3W - injectiongrade, heat-resistant and aging resistant. Parts suitable forlong-term high-temperature use.

PA66 nylon B3S - injectiongrade. Easy to flow, fast curing, containing stabilizers. Suitablefor thin-walled products such as covers, fixtures, pins, plywood,and fasteners.