抗紫外线PC 德国科思创（拜耳） 1837 高粘度 耐高温

抗紫外线PC 德国科思创（拜耳） 1837 高粘度 耐高温

抗紫外线PC 德国科思创（拜耳） 1837 高粘度 耐高温

抗紫外线PC 德国科思创（拜耳） 1837 高粘度 耐高温

抗紫外线PC德国拜耳2607 抗紫外线PC德国拜耳2607 抗紫外线PC德国拜耳2607

干燥

为了保证制件质量，成型前，必须对原料充分干燥。干燥可采用沸腾床干燥（温度120～130℃，时间1～2h）；真空干燥[温度110℃，真空度0.96MPa（720mmHg）以上，时间10～25h]；普通烘箱干燥（温度110～120℃，时间25～48h）。干燥时间不能过长，否则树脂颜色加深，容易造成性能下降。于燥后水分应不

强度随相对分子质量的增加而提高，熔融黏度也随相对分子质量的增加而明显地加大。用于注射成型的聚碳酸酯相对分子质量一般为2万～4万。

聚碳酸酯的熔融黏度较尼龙，聚苯乙烯、聚乙烯大得多，这对注射充模有影响，因为流动长度随黏度增大而缩短。其流动特性接近于牛顿流体，熔融黏度受剪切速率的影响较小，对温度的变化则十分敏感。在注射成型过程中，通过提高温度来降低黏度比增大压力更有效。[1] 

成型工艺编辑

1．原料的预热大于0.03%。注射时，料斗应是封闭的，其中可加设加热装置（红外线灯或电加热），料温允许达到120℃，借以防止干燥后的树脂再吸湿。料斗的加料量应不超过0.5～1h的用量。已干燥好的物料如不立用，应在密闭容器内保存。使用时，应在120℃温度下再千燥4h以上。湿含量是否合格，快的检验是在注射机上米用“对空注射”法，如果从喷嘴缓慢流出的物料是均匀无色、光亮无银丝和气泡的细条，即为合

成型温度的选择与树脂相对分子质量及其分布，制件的形状及

聚碳酸酯的熔融黏度较高，成型薄壁或形状复杂的制件需要较大的注射压力。使用柱塞式注射机，一般注射压力为100～160MPa，而螺杆式注射机为80～130MPa。保压时间对制件内应力影响较大。为获得各项性能良好的制件，选用高料温和低压力是适宜的，这将减少制品的残余压力。保压时间过长，不仅内应力大，制件易开裂使强度降低，会延长成型周期。通常注射速度约在8～10m/s之间。

4．模具温度

供应高黏度PC德德国科思创 3103.3105.3107.3156.3158.8025.8035.9415.6555.KU1-1244.2607.2805.3208.DP1-1828.6717. 
供应Bayer高黏度PCRX1805.1095.2607.3206.9425.6585.1844.ET3117.ET3127.1239.1804.8345.
供应高黏度PC 德国科思创————

供应耐寒超韧级PC德国科思创 DP1-1837.DP1-1820.

供应Bayer超韧耐寒级PC ————

hemhaghenmarake haprupyava ableeruomenreremp

hemvekpahenmarake haprupfcha

hemhaghenmarake haprupyavaomenreremplegalegalegakov

There are countless fightingskills in the mainland of Douqi, but most of the popular fightingskills that have been passed down are only around the yellow level.To obtain higher level fighting skills, one must join a sect or aDouqi academy on the mainland.

hemhagosjailcilikieavavetañbarupyava ableeruomenrerempèteve1-1837. èteve1-1820

hemvekpaeavavetakiosjailciliruplegalegalegakov

After induction and statistics,Douqi Continent divides the level of Douqi techniques into fourlevels and twelve levels from high to low: Tian, Di, Xuan,Huang

And each level is divided intothree levels: initial, intermediate, and high

The level of the Douqicultivation technique is also the key to determining the level offuture achievements. For example, those who cultivate theintermediate level of the Xuan level technique are naturally a bitstronger than those of the same level who cultivate the advancedlevel of the Yellow level technique.

The power of the mainland andthe strength of the debate depend on three conditions.

Firstly, the most importantthing is, of course, one's own strength. If one's own strength isonly at the level of a Star Fighter, even if one cultivates a rareskill of the Heavenly Level, it is difficult to defeat a Fighterwho cultivates the Yellow Level skill.

Secondly, there are those whoare strong at the same level of martial arts. If your martial artslevel is much higher than the opponent's, then during thecompetition, various advantages are known at a touch.

The last one is calledDouji

As the name suggests, this is aspecial skill for wielding fighting energy. Fighting skills aresuperior to those on the mainland and have different levels.Overall, they are also divided into four levels: Heaven and Earth,Dark and Yellow.