用途：

各类聚四氟乙. 烯制品已在化工、机械、电子、电器、航天、环保和桥梁等国民经济领域中起到了举足轻重的作用。

四氟乙.烯板适用于-180℃~+250℃温度下，主要用作电器绝缘材料及接触腐蚀介质的衬里、支承滑块、道轨密封件及润滑材料，富柜家具把它用于轻工业中，广泛应用于化工、医药、染料业容器、贮槽、反应塔釜、大型管道的防腐衬里材料；航空、军事等重工业领域；机械、建筑、交通桥梁滑块、导轨；印染、轻工、纺织业的防粘材料等．

PTFE美国杜邦7A X

外观标准：

(1)板材的颜色为树脂本色。

(2)应质地均匀，外表平整，不允许有裂纹、气泡、分层、机械损伤、刀痕等缺陷。

(3)允许有轻微云斑状的松紧现象。

(4)允许有10×10cm面积上存在直径为0.1-0.5mm非金属杂质不超过1个，直径为0.5-2mm的非金属杂质不超过1个。

Zonyl MP1100（4微米）

ZonylMP1100氟添加剂是一种白色的自由流动的PTFE粉末，旨在作为其他材料中的添加剂使用，以提供低表面自由能和其他氟聚合物特性。特别重要的是，已有发现证明它非常适用于油墨和涂层应用，这些应用对颗粒的均匀性有一定要求。与塑料和弹性体一起使用时，还可增强润滑性能和耐磨损性能。如果将其加入润滑剂中，可以增强严苛条件性能。Zonyl?MP1100可应用于–190到250°C(–310到480°F)的温度条件。

Zonyl MP1200（3微米）

使用，以提供低表面自由能和其他氟聚合物特性。特别重要的是，已有发现证明它非常适用于油墨和涂层应用，这些应用对颗粒的均匀性有一定要求。与塑料和弹性体一起使用时，还可增强润滑性能和耐磨损性能。如果将其加入润滑剂中，可以增强严苛条件性能。ZonylMP1200可应用于–190到250°C(–310到480°F)的温度条件。

Teflon®PTFE 7A X

Polytetrafluoroethylene

DuPont Fluoropolymers

产品说明：

Teflon ® PTFE 7A X is a white powder with small particle sizeand high bulk density. The small particle size of Teflon ® PTFE 7AX helps to minimize voids even at relatively low molding pressures.High bulk density increases the size of moldings possible from agiven mold or press opening. Teflon ® PTFE 7A X is preferred forlarge moldings, such as billets, requiring optimum mechanical andelectrical properties. It is also used in a mixture with fillerswhen they are added to modify the mechanical properties ofmoldings. Properly processed products made from neat Teflon ®PTFE7A X provide the superior properties typical of the fluoroplasticresins: retention of properties after service at 260 °C (500 °F),useful properties at -240 °C (-400 °F), chemical inertness tonearly all industrial chemicals and solvents, and low friction andanti-stick surfaces. Dielectric properties are outstanding andstable with frequency and temperature. Molded products havemoderate stiffness and high elongation.

Teflon ® PTFE 7A X resists ignition and does not promote flame
spread. When ignited by flame from other sources, the contributionof heat is small and with little smoke. Statements, or data,regarding behavior in a flame situation are not intended to reflecthazards presented by this or any other material when under actualfire conditions.

Typical Applications
Many end products are fabricated from moldings of Teflon ® PTFE 7AX, including skived film and sheet, gaskets, packings, mechanicalseals, bridge or pipeline bearing pads, shaft bearings, electricalinsulators, piston rings, expansion bellows, diaphragms, andchemical linings. The use of fillers provides a wide choice ofmodified mechanical properties.

物性信息：